Kalinina, N. E.Hlushkova, D. B.Voronkov, A. I.Kalinin, A. V.Stepanuk, A. I.Voronova, E. M.Serzhenko, I. O.Калініна, Наталія ЄвграфівнаКалінін, Олександр ВасильовичГлушкова, Діана БорисівнаВоронков, Олександр ІвановичСтепанюк, Андрій ІвановичВоронова, Єлизавета МихайлівнаСерженко, Іванна ОлегівнаКалинина, Наталия ЕвграфовнаКалинин, Александр ВасильевичГлушкова, Диана БорисовнаВоронков, Александр ИвановичСтепанюк, Андрей ИвановичВоронова, Елизавета МихайловнаСерженко, Иванна Олеговна2021-02-162021-02-162020Influence of nanodispersed compositions on structure formation of high-strength aluminum alloys / Kalinina N. E., Hlushkova D. B., Voronkov A. I., Kalinin A. V.,Stepanuk A. I., Voronova E. M., Serzhenko I. O. // Вiсник Харкiвського нацiонального автомобiльно-дорожнього унiверситету : зб. наук. пр. / М-во освiти i науки України, Харків. нац. автомоб.-дор. ун-т ; редкол.: А. Г. Батракова (гол. ред.) та iн. – Харкiв, 2020. – Вип. 91. – С. 34–39.2219-5548https://dspace.khadi.kharkov.ua/handle/123456789/3474An analytical review of the state of the problem of aluminum alloys modification was performed. The absence of a unified approach to solving the problem has been established, which is asso-ciated with the complexity of the process of modifying multicomponent alloys. The aluminum alloys of the AL-Zn-Mg-Cu system were studied. As a modifier, a composition based on nanodispersed powders of titanium and boron with fractions of up to 100 nm, obtained with plasma-chemical synthesis, is proposed. The structure, phase composition, and properties of the test samples were studied before and after modification with methods of optical microscopy, X-ray diffraction analysis, and X-ray spectral analysis. In the modified B95 and B96 alloys, grain refinement and structure stabilization were achieved. Determination of the crystal lattice parameters of the alloys showed an increase in the period of lattice of the modified samples by 1.02%. The microhardness of α-Al, the solid solution, was increased from 1080 to 1500 MPa. The phase composition of B95 and B96 alloys is represented with the intermetallic phases CuAl2, MgZn3, Mg2Zn3, Mg2Si, FeAl3, TiB2, TiAl3, as well as phases of complex composition. The maximum grain refinement and increase in the mechanical properties of the alloys were achieved upon modification of 0.05% Ti and 0.005% B, which is explained by the formation of dispersed strengthening intermetallic phases of complex composition in the center of the grains.enaluminum alloysstructurephase compositionintermetallic phasesnanomodifiertitaniumboronалюмінієві сплавифазовий складструктураінтерметалічні фазинаномодифікатортитанборалюминиевые сплавыфазовый составинтерметаллические фазынаномодификаторArticle620.175.2:669.1510.30977/BUL.2219-5548.2020.91.0.34